精品亚洲成a人在线观看,成人性生交大片免费看小说,亚洲国产成人综合精品,成人国产欧美大片一区

行業動態

行業動態

使用冷干機應注意哪些事項?

來源:杭州優聯超濾設備有限公司  日期:2017-05-23 09:10:49  點擊:2859  屬于:行業動態
①壓縮空氣的流量壓力、溫度應在銘牌允許范圍內; ②安裝地點應通風,少粉塵,機器周圍有足夠散熱和檢修空間且不能在室外安裝,以避免雨水及陽光直射;
使用冷干機應注意下列事宜:
Use the person who should pay attention to the following matters:
①壓縮空氣的流量壓力、溫度應在銘牌允許范圍內;
(1) the flow of compressed air pressure, temperature should be in the range of allowable nameplate;
②安裝地點應通風,少粉塵,機器周圍有足夠散熱和檢修空間且不能在室外安裝,以避免雨水及陽光直射;
(2) the installation location should be ventilated, less dust, the machine has enough heat and maintenance space around and cannot be installed outdoors, to avoid the rain and sun;
冷干機一般允許無基礎安裝,但地面必須找平;
(3) person who generally allow no base installation, but must ground leveling;
④應盡量靠近用戶點,避免管線過長;
(4) should be close to the user points, as far as possible to avoid the pipe is too long;
⑤周圍環境中不應有可檢測到的腐蝕性氣體,尤其注意不能與氨制冷設備共處一室;
(5) should not be in the surrounding environment can be detected by corrosive gas, especially pay attention to cannot coexist one room with ammonia refrigeration devices;
⑥冷干機前置過濾器的過濾精度要適當,過高精度對冷干機并無必要;
Those person who must be properly pre filter filtration precision, high accuracy, with no need for person;
⑦冷卻水進出管要獨立設置,尤其是出水管不可與其他水冷設備共用,避免壓差引起排水受阻;
All landowners of cooling water in and out of the tube to independent setting, especially the outlet pipe is Shared with other water cooling equipment, avoid pressure difference causes drain is blocked;
⑧任何時間都要保持自動排水器排水暢通;
Any time today to keep clear of automatic drainer drainage;
⑨不要連續啟動冷干機;
Pet-name ruby do not consecutive start person;
⑩冷干機實際處理壓縮空氣的參量指標,特別是進氣溫度、工作壓力與額定值不符時,要按樣本提供的“修正系數”進行修正,以避免出現超負荷運行。
Attending person who actually handle the parameter index of compressed air, especially the inlet temperature, the working pressure is not in conformity with rating, according to a sample provided by the correction coefficient modification, to avoid overload operation.